Pass4sure 300-080 Certification Real Test Questions

QUESTION 3


Which two troubleshooting tools would initially be the best to use when troubleshooting the PSTN gateway side of a call routing issue while using Cisco Unified Communications Manager? (Choose two.)

     A.  RTMT trace output
     B.  Cisco IOS debug commands
     C.  Dialed Number Analyzer output
     D.  Cisco Unified Communications Manager alerts
     E.  Cisco IOS show commands

        Correct Answer: BE                                     Pass4sure 300-080 dumps


300-080 Braindumps

Read More

Pass4sure 300-080 Exam Questions

QUESTION 2

When a database replication issue is suspected, which three tools can be used to check the database replication status? (Choose three.)

     A.  Cisco Unified Communications Manager RTMT tool
     B.  Cisco Unified Communications Manager Serviceability interface
     C.  Cisco Unified Reporting
     D.  Cisco Unified Communications Manager CLI interface
     E.  Cisco IP Phone Device Stats from the Settings button
     F.  Cisco Unified OS Administration interface

      Correct Answer: ACD

Read More

Pass4sure 300-080 Real Questions and Answers

QUESTION 1

    To maintain proper database integrity, what is the recommended maximum round-trip delay between multiple Cisco VCS appliances in a cluster?
        A. 10 ms
        B. 15 ms
        C. 25 ms
        D. 30 ms
        E. 50 ms
        F. 80 ms
               Correct Answer:D

Read More

Pass4sure 300-080 Real Questions and Answers Demo

     QUESTION 1

    To maintain proper database integrity, what is the recommended maximum round-trip delay between multiple    Cisco VCS appliances in a cluster?
        A. 10 ms
        B. 15 ms
        C. 25 ms
        D. 30 ms
        E. 50 ms
        F. 80 ms
               Correct Answer:D

Read More

Pass4sure 300-080 Question Answers

          QUESTION 1

    An IP phone that is connected through a Cisco Catalyst 3750 Series Switch is failing to register with the subscriber as a backup server. When the user presses the settings button on the          phone, only the Cisco Unified Communications Manager publisher shows as registered. What is the most likely cause for this issue?

       A. The phone does not have the correct Cisco Unified Communications Manager group in the device configuration page.

      B. The Cisco Unified Communications Manager group that is applied through the device pool is misconfigured.

     C. The ip-helper address command for the subscriber is not configured on the switch port.

      D. The subscriber does not have the correct device pool configured.

      E. The enterprise phone configuration does not have the call control redundancy enabled.

       Correct Answer: B

Read More

CompTIA Security 300-080 + Certification Exam Question

Question No : 2

   An IP phone that is connected through a Cisco Catalyst 3750 Series Switch is failing to register with Cisco        Unified Communications Manager. When the user

  presses the settings button on the phone, the Operational VLAN ID shows a blank entry. What is the most         likely cause for this issue?

   A. The switch may not be supplying inline power.

    B. The spanning tree portfast command needs to be removed.

   C. The trunk encapsulation is missing. The trunk must be configured for dot1.Q.

  D. Cisco Discovery Protocol is disabled on the switch.

   E. The Operational VLAN ID of the phone always shows as blank. The Admin. VLAN ID should be 110.

          Correct Answer:D

Read More

Pass4sure 300-080 CompTIA Demo Question

Question No : 3

  You configured a Cisco ISR G2 as a SIP gateway, but the gateway does not show that it is registered with         Cisco Unified Communications Manager. What is causing this issue?

    A. Cisco Unified Communications Manager does not support SIP gateways.

    B. The gateway does not have the UC license installed.

    C. The gateway does not have Cisco Unified Border Element session licensing.

    D. Cisco Unified Communications Manager does not show a SIP gateway as registered if it is not properly             configured.

     E. Cisco Unified Communications Manager never shows a SIP gateway as registered even when it is                     properly configured.

    F. The Cisco ISR G2 cannot be a SIP gateway.

C           Correct Answer:E

Read More